可以為螺栓拉伸器提供液壓動力，產品靜態水壓測試及破壞性的試驗，流體的壓力輸出及增壓，高院研究單位實驗室反應釜高壓介質的充裝，凡事需要進行液體壓力測試的場合都必須進行極為嚴格的壓力測試。
It can provide hydraulic power for bolt stretchers, conduct static water pressure testing and destructive testing of products, output and pressurization of fluid pressure, and fill high-pressure medium in reaction vessels of research institutes. In all situations where liquid pressure testing is required, extremely strict pressure testing must be carried out.
氣液增壓泵有如下幾個特點，體積小，輸出壓力高壓，維護方便，氣動增壓類產品，操作極其方便，可以作為水壓測試臺 爆破測試臺 脈沖試驗機等的核心部件-液壓動力。無需用電，工廠的壓縮氣體可以為動力源。
The gas-liquid booster pump has the following characteristics: small size, high output pressure, convenient maintenance, pneumatic booster products, extremely convenient operation, and can be used as the core component of hydraulic power testing equipment, such as hydraulic pressure testing equipment, explosion testing equipment, pulse testing machines, etc. No electricity is required, and the compressed gas in the factory can be used as the power source.
氣液增壓泵的工作原理，它是使用壓縮空氣為動力源，輸出液壓力與驅動氣源壓力成比例。通過對驅動氣源壓力的調整，便能得到相應的液壓力。當驅動氣源壓力與液壓力平衡時，氣動增壓泵便停止充壓，輸出液壓力也就穩定在預調的壓力上。
The working principle of a gas-liquid booster pump is to use compressed air as the power source, and the output liquid pressure is proportional to the driving air source pressure. By adjusting the pressure of the driving air source, the corresponding hydraulic pressure can be obtained. When the pressure of the driving air source is balanced with the hydraulic pressure, the pneumatic booster pump stops charging, and the output hydraulic pressure stabilizes at the preset pressure.
氣體增壓泵的換向閥后面的小孔，還有驅動端旁邊的小孔，可以理解為呼吸孔，那么如雜質過多，或者進行泵體內部會對氣體增壓機造成缸體劃傷，密封圈磨損，這樣會是增壓機的壽命縮短，不利于氣泵的正常工作。
The small hole behind the directional valve of the gas booster pump, as well as the small hole next to the drive end, can be understood as a breathing hole. If there are too many impurities or if the pump body is inside, it will cause scratches on the cylinder body and wear on the sealing ring of the gas booster pump. This will shorten the service life of the booster pump and is not conducive to the normal operation of the gas pump.
另外氣體增壓泵的驅動端水分一定要嚴格控制，水分過多由換向閥進入到驅動缸體，是內部的潤滑脂稀釋，長時間工作潤滑脂會通過消音器排放到大氣中，泵體內部密封脂缺少，使內部活塞工作阻力增大，會增大增壓機密封圈的磨損，不利于增壓機的使用。
In addition, the water content at the driving end of the gas booster pump must be strictly controlled. Excessive water content enters the drive cylinder body through the directional valve, which dilutes the internal lubricating grease. Long term working lubricating grease will be discharged into the atmosphere through the silencer. The lack of sealing grease inside the pump body increases the working resistance of the internal piston, increases the wear of the booster seal ring, and is not conducive to the use of the booster engine.
再者，氣體增壓泵的被增壓介質一定不要有水分，或者雜質，如果發現要及時清理維護。氣體增壓機內部雜質及水分嚴重過多會造成很嚴重的影響，比如導致氣動增壓機內表面生銹、老化，嚴重導致使用壽命縮短。
Furthermore, the pressurized medium of the gas booster pump must not contain moisture or impurities. If found, it should be cleaned and maintained in a timely manner. Excessive impurities and moisture inside the gas booster can have a serious impact, such as causing rust and aging on the inner surface of the pneumatic booster, seriously shortening its service life.
Thank you for reading. The source of this article is: Gas Booster Pump. For more information and questions, please click on: http://www.idleaf.com We will continue to work hard to provide you with services. Thank you for your support!
